logo
Shandong Lift Machinery Co.,Ltd
Products
News
Home > News >
Company News About Latin American Workshops Move to Galvanised and Mobile Scissor Car Lifts as Salt Air Sets the Spec
Events
Contacts
Contacts: Mr. Owen
Fax: 86-531-66957937
Contact Now
Mail Us

Latin American Workshops Move to Galvanised and Mobile Scissor Car Lifts as Salt Air Sets the Spec

2026-11-20
Latest company news about Latin American Workshops Move to Galvanised and Mobile Scissor Car Lifts as Salt Air Sets the Spec

wo conditions define scissor car lift specification across Latin America, and neither appears in a standard catalogue. The first is salt air. A painted lift on the coast at Veracruz, Santos or Guayaquil starts bleeding rust at the weld seams within eighteen months, and once corrosion reaches the pivot bushes the arm cannot be saved. The second is tenancy: a workshop renting a bay in Lima or Bogota cannot cut a pit into somebody else's floor.

Hot dip galvanized 4 ton scissor car lift with 85 micron zinc coating for coastal workshops

Galvanising Beats Paint on the Coast

For coastal sites the frame is hot dip galvanized after fabrication, giving an average 85 micron zinc layer on every surface, including the inside of the rectangular tube and the weld toes where paint cannot reach. Salt spray testing runs to 480 hours with no red rust. The electrics matter just as much: an IP65 sealed cabinet with stainless hinges and a breather vent prevents the condensation that kills contactors during day night temperature swings, and hard chrome or stainless piston rods resist the pitting that destroys cylinder seals.

Brazilian buyers ask about voltage first. Units for Brazil ship wired for 380V 60Hz three phase with NBR compliant terminal marking so customs clearance does not stall, while Mexico takes 220V or 440V by state. Spanish and Portuguese manuals and nameplates are included.

Mobile scissor car lift on lockable casters, no pit and no foundation anchors required

Mobility Solves the Rented Bay Problem

A portable unit needs no pit and no anchors. Six polyurethane casters, four of them lockable, roll the machine into a corner at closing time, and a hand pump circuit keeps work going through power cuts, a real consideration in parts of Peru and Colombia. Capacity of 3,000 kg with a 2,400 mm lift height covers brake, tyre and suspension work on passenger cars and compact SUVs, and the base frame is welded from 100 x 100 mm square tube rather than bolted channel because portable lifts take more handling abuse than fixed ones.

The third requirement, increasingly common in Argentina, is alignment capability. A scissor platform built for four wheel alignment carries two recessed 360 degree front turntables, two low friction rear slip plates and runways levelled to plus or minus 1 mm, with a 5,600 mm deck so a pickup sits fully on the platform. Jacking beams can be added for strut work without moving the vehicle off the alignment position.

5 ton wheel alignment scissor platform with front turntables, rear slip plates and 3.5 m lifting height

Matching the Machine to the Site

Site Condition Recommended Configuration Key Specification
Coastal, salt air, outdoor bay Hot dip galvanized 4 t 85 micron zinc, IP65 cabinet, 480 h salt spray
Rented premises, no civil works Portable mobile 3 t 6 casters, hand pump backup, no pit
Alignment bay, long wheelbase pickup 5 t alignment platform Turntables, slip plates, +/- 1 mm levelling

Before a quotation is issued, three questions decide the configuration, and buyers who answer them early avoid a redesign later:

  • Is the site within five kilometres of the sea, or does the bay open directly to the street where salt spray reaches it?
  • Is the building owned or rented, and can a 750 to 800 mm pit be cut without landlord approval?
  • Does the bay need four wheel alignment capability, or is general service and tyre work the main revenue?

Shipping runs 28 to 38 days to Manzanillo, Veracruz, Santos, Callao, San Antonio, Cartagena or Buenos Aires depending on routing. Because the nearest dealer can be a continent away, we recommend a first year spare kit per machine: one seal set, one hose assembly and a set of caster wheels.

The machines described here are produced by Shandong Shiqi Machinery Co., Ltd, a lifting equipment maker in Shandong, China, founded in 2001 with 20 to 200 employees and 50 to 60 percent of output exported. The company holds CE certification, builds OEM versions for importers and supplies Spanish and Portuguese manuals, and its regional experience comes from eight years of coastal installations.

Every unit is pressure tested at 1.5 times working pressure, run through 40 to 60 lift cycles and proof loaded at 1.2 times rated capacity before packing, with records attached to the shipping documents. For coastal customers the practical lesson from eight years of service reports is simple: the structure rarely fails first, the electrics and the piston rod surface do. Specify those two items properly and a galvanized lift will outlast the building it stands in.

Send the port of discharge, the site power supply and a photograph of the bay, and we will return a dimensioned proposal with drawings, test data and a loading plan for the container.